|Published (Last):||5 January 2015|
|PDF File Size:||5.50 Mb|
|ePub File Size:||7.8 Mb|
|Price:||Free* [*Free Regsitration Required]|
Akinokus Do not use pliers, otherwise the connector may be damaged. Type of noise Noise intrusion path and countermeasure Before countermeasure Noise e3c-v1g from the noise source through the frame metal. Typical examples include the minimum sensing object, engineering data, step height detection data, and selection list for specifications. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.
Cable Bending Destruction Test Tough Wire Breaking Test With current flowing, bending is repeated to check the number of bends until the current stops. Power Supply Types An unsmoothed full-wave or half-wave rectifying power supply cannot be used. AC 2-wire Sensors Example: EE11 Check the parallel movement distance range in the catalog, verify the set distance between adjacent Sensors, and install the Sensors accordingly at a distance at least 1.
Lowering the sensitivity will generally help. Do not subject a shielded cable or coaxial cable to tension. Precautions for Safe Use To ensure safety, always observe the following precautions. This information by itself is not suf? Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.
Ambient Conditions Do not use this Sensor in the following locations. Organic solvents will dissolve the surface. Refer to the values in the above table to check bend-resistant performance under actual working conditions. In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
Mutual Interference Mutual interference is a state where an output is unstable because the Sensors are affected by light from the adjacent Sensors. Omro, if the workpieces are close to the Photoelectric Sensors, light from the adjacent Emitter may be received and cause the Sensor to change to the incident light state.
The axis from the center of the lens ec3-vs1g the center of the beam for the Emitter and the axis from the center of the lens to the center of the reception area for the Receiver. Be sure to insert a load when connecting the power supply. If Sensors are mounted in opposite each other, slant the Sensors as shown in the following diagram.
Insert a capacitor e. Doing so may cause explosion or burning. Through-beam Sensors Reflective Sensors 1 If Sensors are mounted in close proximity, ec3-vs1g Sensors with the interference prevention function. Cable diameter Less than 4 mm 4 mm or greater Tensile strength 30 N max. Systems, machines, and equipment that could present a risk to life or property. To maintain the fiber characteristics, make sure that the lock is released before removing the fibers.
Repeated Bending Normally, the Sensor cable should not be bent repeatedly. If copying or transmitting this catalog to another, please copy or transmit it in its entirety. Hold the connector cover to connect or disconnect the connector. The lens, however, is plastic.
For this type of application, separate the Sensors by at least 1. Do not use it for such purposes. Separate the noise source and the Sensor to a distance where noise does not affect operation. Strong, conductive electrical wire 2 x 0. This catalog is protected by copyright and is intended solely for use in conjunction with the product.
This may weaken performance. Radiant noise Ingress of high-frequency electromagnetic waves directly into Sensor, from power line, etc. Separation from High Voltage Wiring Method Do not lay the cables for the Sensor together with high-voltage lines or power lines. Typical measures are as given in the following table. Do not use thinner or other organic solvents. If the connector is not connected securely, the connector may be disconnected by vibration or the proper degree of protection of the Sensor may e3c-vx1g be maintained.
Please know and observe all prohibitions of use applicable to the products. Any exceptions to this rule are indicated in Safety Precautions in individual product information. Be sure to connect or disconnect the connector after turning OFF the Omro. Although the bending repetition tolerance of a standard cable is approximately 13, times, robot cable has an excellent bending tolerance of approximatelytimes. The lens, case, and fiber covering are made of plastic, so this setup cannot be used if there is a possibility of contact with solvents that will corrode or degrade e.
Dirt should be gently wiped off with a dry cloth. Fiber insertion mark Fiber 9mm 2 Removing Fibers Open the protective cover, lift up the lock lever, and pull out the fibers. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Most 10 Related.
All the products will packing in anti-staticbag. Ship with ESD antistatic protection. We will inspect all the goods before shipment,ensure all the products at good condition and ensure the parts are new originalmatch datasheet. After all the goods are ensure no problems afterpacking, we will packing safely and send by global express. It exhibitsexcellent puncture and tear resistance along with good seal integrity. Guarantees 1. We provide 90 days warranty.
E3C-VS1G OMRON PDF
Mojin In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. Do not subject a shielded cable or coaxial cable to tension. Fiber insertion mark Fiber 9mm 2 Removing Fibers Open the protective cover, lift up the lock lever, and pull out the fibers. Strong, e3c-va1g electrical wire 2 x 0. If not grounded, switching noise in the power supply may cause malfunction. Repeated Bending Normally, the Sensor cable should not be bent repeatedly. Power line Work Required for Unconnected Leads Unused leads for self-diagnosis outputs or other special functions should be cut and wrapped with insulating tape to prevent contact with other terminals.